Beginner's Plumbing: The Essentials for Bathtub Installation
Beginner's Plumbing: The Essentials for Bathtub Installation
Blog Article
Each person maintains their personal piece of advice involving How to Install a Bathtub.
Setting up a tub isn't exactly rocket science, yet it does need solid plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably tough project. If the old bathtub is readily obtainable, the job can relocate immediately; if you have to open up a wall to get rid of the old tub as well as place the new tub, the job is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. Ensure you have actually qualified yourself for the task and fit trying it. Instead of hiring a specialist to take over a halfway-completed task, it is much better to think about utilizing one prior to you begin. Possibilities are you may need a specialist plumber to make tube links.
This post will certainly assist you set up a new bath tub in your washroom if you have already acquired a new bathtub as well as don't require to change the arrangement of your previous water pipes.
Your devices and product checklist must comprise the following:
Getting ready for the Installment
Firstly, the supporting framework supplied with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps system to prevent pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you use all of the provided washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should now be ready to be suited its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you need to do is disconnect the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather bothersome because of the restricted gain access to that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Tub
Using both wood boards under its feet, put the bathtub in the required position. The wood boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small points.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by checking the level and changing the feet on the bathtub until the level reviews degree.
To set up taps, fit all-time low of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression join; then do the very same for the other tap.
Activate the supply of water and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as likewise check the overflow outlet and the typical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the producer's instruction manual. Tiling as well as sealing around the bath tub needs to wait until the tub has been utilized a minimum of when as this will certainly settle it into its last setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the various other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Protect the tap in position with the manufacturer given backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The previous kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break an inflexible seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and also can securing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our article on How to Install a Bathtub. Thank you for taking time to browse our piece of content. Do you know about anybody else who is excited by the subject? Feel free to share it. Thank-you for going through it.
Service excellence here. Report this page